Hull Industries' Complete Molding Solution Process - Automatic Material Loading - Mold Design/Presses - Automated Parts Handling - Deflashers - Corona Beam Inspection - Hull Industries' Complete Molding Solution Process

Press Selection Checklist/Specification

Thank you for your interest in our presses, we are eager to assist you so please be kind enough to provide us important information.

  Shipping and Mailing Address:

Hull Industries, Inc.
59 Industrial Drive
New Britain PA 18901 USA

 Telephone:

888-567-0983 (Toll Free)
215-230-4260 (Local Voice)
215-230-4261 (Local Fax)

Email Address:

info@hullindustries.com
Press Selection Checklist / Specification
 
* Name   Privacy Note:
All information provided in this request form will be used solely to provide you with the information that you are requesting. This information will not be shared with anyone outside Hull Industries.

Thanks for your interest in our products and services.
*
Email
  
  Company  
 

Address

  
   
 
City
   Preferred Method to be Contacted:
 
State
  
  Zipcode
How did you hear about us:
  Country  
  Province/County    
  Phone    
  Fax    
  Type of press: Transfer Compression Shuttle Injection Automatic Compression
    For Compression Press:  Downward Acting Upward Acting
  Type of molding material
(ie: BMC, Polyester, Composite, Etc.)
  Material will be in what form
(ie: Grandular, Bulk, Sheet, Etc.)
  How will material be loaded into press
(ie: Manually, Automatically-Feeder System)
  Size of part to be molded
(Length / Width / Height in inches)		 L   W   H 
  Number of cavities in mold
  Amount of molding material    (transfer press only)
  Clamp tonnage requied
  Transfer tonnage required
  Hydraulic system operation pressure (psi)
(Our standard press design is based on 3000 psi)
  Clamp stroke required   (inches)
  Transfer stroke required   (inches)
  Ejector stroke required   (inches)
  Daylight required   (inches)
  Tie rod spacing (left to right) - (transfer, compression,
shuttle, automatic compression presses)		   (inches)
  Tie rod spacing (front to back) - (transfer, compression,
shuttle, automatic compression presses)		   (inches)
  Tie rod spacing (front to back) - (injection press only)   (inches)
  Tie rod spacing (top to bottom)   (inches)
  Platen size (left to right)   (inches}
  Platen size (front to back)   (inches)
  Minimum mold height required   (inches)
  Height required from floor to platen   (inches)
  Are there space requirements that must be considered   Overall height (inches)
  Floor Space - length and width - (transfer, compression,
shuttle, automatic compression presses)		   Left to right (inches)
  Front to Back (inches)
  Floor Space - length and width - (injection press)   Length (inches)
  Width (inches)
  Heat Platens Required Yes No
  Number of heating zones per platen half
  Heater power required per platen (KW)
  Clamp - fast close   (inches/minute)
  Clamp - pressing   (inches/minute)
  Transfer - fast close - (transfer press only)   (inches/minute)
  Transfer - retract- (transfer press only)   (inches/minute)
  Electrical Requirements - please provide any special requirements for the electric motor, heat and controls (please refer to our product brochures for our standards.)
Options:
  "Smart Mold" System   (proportionall velocity and pressure control (transfer and injection presses) Yes No
  Injection/Compression circuit - (injection press) Yes No
  BMC stuffer - (injection press) Yes No
  Hydraulic Core Pull) Yes No
  Proportional position control - (compression press) Accuracy Required Yes No
  Proportional pressure control - (compression press) Accuracy Required Yes No
  Other special features or requirements: (please be specific)
 
 
The Wright Agency Appointed

The Wright Agency appointed in Western NY, Western PA, and West Virginia. [More ...]
 

Recent Orders

- Cryogenic Deflashing System - purchased by a large manufacturer of seals for use in their R&D Department. - 400 Ton Compression Press - purchased by the military for the development of new materials for personnel protection. - 200 Ton Injection Molding Machine - purchased by a thermoset materials processor in the electrical industry. [More ...]